IVECO-AMT Eurocargo MLС140Е25 Isothermal van
- Customer pickup,
- Courier
- In detail
- Car makeIveco
- ConditionNew
- Wheel formula4x2
- Type of vanRefrigeration
Sandwich panel van 7500x2600x2500 (IVECO - AMT Eurocargo)
IVECO Car Chassis Technical Specifications - AMT Eurocargo ML C140E25
| Characteristics | Base chassis IVECO - AMTEurocargo MLС 140 Е25 |
| Wheel formula | 4 × 2 |
| Appointment | road |
| Cabin | MLС (short, without berth) |
| Ground clearance, mm (P) | 179 |
| Gross vehicle weight, kg | 14,500 |
| Front axle load, kg | 5 100 |
| Rear axle load, kg | 9 500 |
| The maximum mass of the road train, kg | 26,500 |
| Engine | TECTOR 6 5.88 L |
| Power, kW / hp | 250 |
| Max. power, hp / kW / rpm | 251/185 / 2080 - 2700 |
| Tires | 850 / 1250 - 2100 |
| Fuel tank | 200 l |
Technical description of the add - on (van, 1 category)
| Characteristics | Base chassis IVECO - AMTEurocargo MLС 140 Е25 |
|---|---|
| External body dimensions, LxWxH (mm) | 7500 × 2600 × 2500/7340 × 2440 × 2320 |
| Net volume of the body cm 3 | 41 |
| Europallet capacity (1200 × 800 mm), units | eighteen |
| Front Panel | Sandwich panel 80 mm, consisting of:
- Galvanized sheet with polymer coating RAL 9003 - Heater Styropen 50 - Galvanized sheet with polymer coating RAL 9003 - Mortgage element for HOU Thermo King T 800 and Carrier S 750 |
| Side panels
Top panel |
Sandwich panel 80 mm, consisting of:
- Galvanized sheet with polymer coating RAL 9003 - Heater Styropen 50 - Galvanized sheet with polymer coating RAL 9003 |
| Rear doors | Sandwich panel 80 mm, consisting of:
- Galvanized sheet with polymer coating RAL 9003 - Plywood 4 mm - Heater Styropen 50 - Galvanized sheet with polymer coating RAL 9003 |
| Bottom | Sandwich Panel 100 mm
- Galvanized steel with polymer coating - Laminated plywood 6 mm - Insulation "Styropen 50", with a transverse force set of 24 mm - Laminated plywood 18 mm - Fiberglass 2.3 mm. with quartz chips |
| Subframe | - Bearing spars connected by U - shaped cross - beams with developed supporting transverse spars in the front and rear of the subframe and with developed lateral support |
| Doorway | - Aluminum profile, petals made of elastic rubber, interchangeable. |
| Wagon Framing | External - aluminum profile. Internal - aluminum profile + fender strip of corrugated aluminum sheet on the front, side walls, doors with a height of 300 mm |
| Rear aperture - PORTAL | With amplifiers in the corners , of brushed stainless steel (Sweden) with a visor, hinge protection and a drain |
| Rear doors | Double, swinging, opening on 270 degrees:
- are fixed in the open position by door magnetic clips ; - each leaf is attached on 4 hinges (FURGOCAR, Italy) |
| Hardware | On each leaf there are two overhead rod (stainless steel pipe, polished) locks of rotary type made of stainless steel with a PUSH handle (FURGOCAR, Italy); |
| Door seals | Aluminum profile, elastic rubber petals, interchangeable |
| Insulation | Styropen - 50 |
| Hardware, hardware | FurgoCar (Italy) |
| Electrical equipment | |
| Interior light | Made by protected bundles of wires. Recessed, turning on / off from the machine - type limit switch, when opening / closing doors |
| - top, side marker lights diode
- reflective tape |
GOST |
| Subframe | |
| Design | Bearing spars connected by U - shaped cross members with developed supporting transverse spars in the front and rear of the subframe and with developed lateral support |
| Coating | Pre - primed paintwork. |
| Side Protection (x2) | Aluminum profile with galvanized steel swivel arms . |
| Wings | Plastic with mud flaps, powder - coated steel mounting bracket. |
| Rear protection | Rubber bumpers to prevent impact during parking maneuvers on the transverse side member of the rear of the subframe. |
| Retractable staircase | 3 - speed, made of galvanized steel, mounted under the transverse side member of the rear of the subframe. |
* It is allowed to use technological layers of insulating materials in sandwich panels.
