- BrandВолжский Химкомплекс
- Country of manufactureRussia
- Form of deliverySheet
Oil and petrol resistant paronite (grade PMB - 1) is produced in the form of sheets according to GOST 481 - 80 and is intended for the manufacture of gaskets that seal detachable joints of various mechanisms. Oil and petrol resistant paronite PMB - 1 is produced in sheets with a thickness of 0.3 to 3.0 mm with dimensions in plan from 400x400 mm to 1000x850 mm. It is efficient in any climatic conditions. For operation in tropical climates, fungicides are used in the production of paronite.
If dimensions allow, then a gasket made of PMB brand paronite is cut from one solid sheet. If a gasket of large dimensions is required (exceeding the dimensions of the sheet), it is allowed to manufacture gaskets from paronite in parts, by means of an adhesive joint.
Scope of paronite PMB - 1
Maximum pressure, MPa
Operating temperature range, ° C
Type of sealed connection
|Oil fractions, heavy and light refined products||16.0||- 40 . . . + 250||Thorn - groove, trough - ledge connections; it is possible to seal "smooth" joints at pressures up to 2.5 MPa||Pumps, vessels, apparatus, pipelines, compressors, internal combustion engines, etc.|
|Liquid VPS||16.0||- 40 . . . + 100|
|Sea water||10.0||- 2 . . . + 50|
|Freon grades 12, 22, 114V - 2||2.5||- 50 . . . + 150|
The recommended roughness parameter of the sealed surfaces is no more than Rz 40 microns.
Physical and mechanical parameters of PMB - 1
|Specific weight of paronite, g / cm3||1.5 . . . 2.0|
|Conditional tensile strength (when a force is applied in the transverse direction), MPa||20.0|
|The increase in mass after 5 hours of keeping the material in:
- in aviation oil of the MS - 20 (or MK - 22) brand (at t + 150 ° C), % ;
- in oil of MK - 8 brand (at t + 100 ° C), % ;
- in a 10% solution of nitric acid (at t + 100 ° C), % ;
- in a 10% sulfuric acid solution (at t + 100 ° C), % ;
|Relative deformation under compressive load (35 MPa), %||2 - 12|
|Recoverability after removing the compressive load (35 MPa), % , not less||thirty|
|WORKSPACE||T, ° C||P, MPa|
|Ammonia liquid and gaseous||110||2.5|
|Coke oven gas||490||6.4|
|Oxygen and nitrogen liquid||- 182||0.25|
|Oxygen and nitrogen gaseous||150||five|
|Liquefied and gaseous hydrocarbons||60||2|
|Light oil products (gaysol, reflux, gasoline, kerosene)||200||2.5|
|Heavy and light oil products (diesel fuel, fuel oil, paraffin, tar, asphalt, bitumen)||300||2|
|Oil fractions (diesel, automotive, aviation, industrial, turbine, transformer oils)||150||2.5|
|Compressibility at 35 MPa||5 - 16%|
|Recoverability after relieving pressure 35 MPa||40%|
|Density||1.5 - 2.0 g / cm3|
Reception and storage
Oil - resistant paronite and products from it are accepted in lots. Each batch in the amount of 100% is subjected to visual quality control, and selectively - for compliance with the physical and mechanical characteristics established by the interstate standard 481 - 80. Each batch is accompanied by a paronite certificate and a marking label.
Store paronite and products made of it in closed, ventilated and heated rooms, preferably in the original packaging. Storage on shelves and racks is allowed, at a height of at least one meter from the ground. Deformations during storage are not permissible. Storage conditions: relative humidity - no more than 65% ; ambient temperature - up to + 35 ° C. Storage at temperatures below 0 ° C is allowed. At the same time, before cutting the paronite and making seals, the material must be kept for 24 hours at a temperature of + 20 ° C.
It is not allowed to expose the material during storage to direct sunlight, liquids and vapors that can destroy rubber. The minimum distance to heating devices is one meter. Do not store paronite near ozone generating equipment.
Subject to the conditions of transportation and storage in accordance with the requirements of State Standard 481 - 80, the manufacturer's guaranteed shelf life for oil and petrol resistant paronite grade PMB - 1 and products made from it is two years from the date of issue.